HC6DW versions: 15 different intensification factors

PIN: 20-207 bar

PH: 800 bar maximum 

PRETURN: As low as possible (return pressure to tank)

POUTLET: PH = (PIN – PRETURN) I (intensification)

Mounting: Inline tube

Weight: 34.8 kg.

Model versions:

A model = no dump valve
B model = with dump valve
G model = direct proportionally controlled

Material certificate 3.1 on request


The HC6DW is a high flow dual-acting stainless steel 316 L unit which is capable of delivering up to 47.1 l/min flow on the high-pressure end. Like other miniBOOSTER models, the HC6DW raises supplied pressure to a higher outlet pressure and automatically compensates for consumption of oil to maintain the high pressure.

Adjustment of the outlet pressure is carried out by varying the supplied pressure. Relative to its flow capability, the HC6DW is a compact unit weighing 34.8 kg.

Flow rates

Intensification factor
Max. intensified outlet flow
Max. inlet flow


The basic operation is illustrated in the function diagram. Oil is fed through the directional valve CV to the IN port, flowing freely through the check valves 2x KV1, 2x KV2 and DV to the high-pressure side H. In this condition maximum flow through the booster is achieved giving a fast-forward function.

When pump pressure is reached on the high-pressure side H, valves KV1, KV2 and DV will close. The end pressure will be achieved by the oscillating pump units OP1 and OP2 by turns. The unit will automatically stall when end pressure on the high-pressure side H is reached. If a pressure drop on the high-pressure side exists due to consumption or leakage, the OP1 and OP2 units will automatically operate to maintain the end pressure. It is possible to change the high-pressure connection H to the opposite end of the booster.

Function diagram



Dimension drawing 6DW-123-07

Connection types

ConnectionIN / RH1 / H2D1 / D2
11/2" BSPPM30 x 1.51/8" BSPP

High-pressure adapters

High-pressure adapter ordering codes and specifications are shown in the PDF-file: 6DW-900-02

Dynamic seals

CodeSeal materialOutlet pressure
HHH-PUR / H-PURMax 800 bar HP
EEEPDM / EPDMMax 500 bar HP

Fluids and materials

Additional information is available on the site General specifications


Ordering an Ordering an HC6DW

HC6DW-…………..: with Bypass Valve (BPV) without Sequence Valve and Pressure Reducing Valve

HC6DWA-………..: with Bypass Valve (BPV) with Sequence Valve and Pressure Reducing Valve

HC6DWB-………..: without Bypass Valve (BPV) without Sequence Valve and Pressure Reducing Valve

Ordering example of an HC6DW with i = 4.0, DV incorporated, BSPP connections and H-PUR dynamic seals:

HC6DW – 4.0 – B – 1HH for media < 5 cSt (mm2/s) tested in water
HC6DW – 4.0 – B – 1SHH for media > 5 cSt (mm2/s) tested in hydraulic oil

Attention notes!
High-pressure adapter is required, please specify ordering code – see high-pressure adapter table.
High-pressure adapters will be factory mounted.

The G-model is available in 2 variants, when ordering please specify accordingly:

  • Dynamic – low hysteresis: Ordering example of an HC6DW with i = 4.0 RV incorporated, BSPP connections and H-PUR dynamic seals: HC6DW – 4.0 – G – 1SHH
  • Fail safe – high hysteresis: The RV valve opening ratio is to be determined on individual basis. Contact our technical support. Ordering example of an HC6DW with i = 4.0 RV with opening ratio x.x incorporated, BSPP connections and H-PUR dynamic seals: HC6DW – 4.0 – G – x.x – 1HH


  • HC6DW

Intensification, i

  • Select factor
  • See flow rate table

Model version

  • Select type
  • A = without DV
  • B = with DV
  • G = with proportional valve


  • Select thread
  • 1   = BSPP, media < 5 cSt
  • 1S = BSPP, media > 5 cSt

Dynamic seals

  • Select seal type
  • See dynamic seal table

Max. tightening torque BSPP

IN / RD1 / D2
1/2" BSPP1/8" BSPP
with stainless steel washer13.0 da/Nm2.0 da/Nm