HC7W versions: 10 different intensification factors
PIN: 20-207 bar
PH: 2,000 bar maximum for media > 5 cSt (mm2/s)
PH: 1,035 bar maximum for media < 5 cSt (mm2/s)
PRETURN: As low as possible (return pressure to tank)
POUTLET: PH = (PIN – PRETURN) x intensification factor
Mounting: Inline tube
Weight: 1.5 kg.
The HC7W is a very compact high-pressure miniBOOSTER stainless steel 316L unit capable of delivering pressure up to 2,000 bar weighing only 1.5 kg. It is ideal for use with very thin (low viscosity) medias. It is ideal for use in portable applications like on power packs.
The HC7W raises supplied pressure to a higher outlet pressure and automatically compensates for consumption of media to maintain the high pressure. Adjustment of the outlet pressure is carried out by varying the supplied pressure. With the choice of different high-pressure adapters, a variety of threads can be obtained from the M22x1.5 thread in the HP port.
|Max. intensified outlet flow|
|Max. inlet flow|
The basic operation is illustrated in the function diagram. Media is fed through the directional valve CV to the IN port, flowing freely through the check valves KV1, KV2 and DV to the high-pressure side H. In this condition, maximum flow through the booster is achieved, giving a fast-forward function.
When pump pressure is reached on the high-pressure side H, valves KV1, KV2 and DV will close. The end pressure will be achieved by the oscillating pump unit OP. The unit will automatically stall when end pressure on the high-pressure side H is reached. If a pressure drop on the high-pressure side exists due to consumption or leakage, the OP valve will automatically operate to maintain the end pressure.
|Connection||IN / R||H|
|1||1/4" BSPP||M22 x 1.5|
|2||7/16-20" UNF||M22 x 1.5|
High-pressure adapter ordering codes and specifications are shown in the PDF-file: 7W-900-07
Fluids and materials
Additional information is available on the website under Products → General specifications.
Ordering an HC7W
Ordering example of an HC7W with i = 13.0, H1 M22 x 1.5 and H2 19/16-18 UNF.DV incorporated and BSPP connections:
HC7W – 13.0 – B – 12 for media < 5 cSt (mm2/s) tested in water
HC7W – 13.0 – B – 12S for media > 5 cSt (mm2/s) tested in hydraulic oil
High-pressure adapter is required, please specify ordering code – see high-pressure adapter table.
High-pressure adapters will be factory mounted.
The G-model is available in 2 variants, when ordering please specify accordingly:
- Dynamic – low hysteresis: Ordering example of an HC7W with i = 13.0 RV incorporated, H1 M22 x 1.5 and H2 9/16-18 UNF and BSPP connections: HC7W – 13.0 – G – 12S
- Fail safe – high hysteresis: The RV valve opening ratio is to be determined on individual basis. Contact our technical support. Ordering example of an HC7W with i = 13.0 RV with opening ratio x.x incorporated, H1 M22 x 1.5 and H2 9/16-18 UNF and BSPP connections: HC7W – 13.0 – G – x.x – 12S
- Select factor
- See flow rate table
- Select type
- A = without DV
- B = with DV
- G = with proportional valve
- Select thread
- 1 = BSPP, media < 5 cSt
- 1S = BSPP, media > 5 cSt
|Ordering code||IN / R||H1||H2||H3|
|HC7W-___-__-11||1/4" BSPP||M22 x 1.5||-||-|
|HC7W-___-__-21||7/16-20 UNF||M22 x 1.5||-||-|
|HC7W-___-__-12||1/4" BSPP||M22 x 1.5||9/16-18 UNF||-|
|HC7W-___-__-22||7/16-20 UNF||M22 x 1.5||9/16-18 UNF||-|
|HC7W-___-__-13||1/4" BSPP||M22 x 1.5||9/16-18 UNF||9/16-18 UNF|
|HC7W-___-__-23||7/16-20 UNF||M22 x 1.5||9/16-18 UNF||9/16-18 UNF|
Max. tightening torque BSPP
|IN / R|
|with stainless steel washer||4.0 da/Nm|
Max. tightening torque UNF
|IN / R|
|with o-ring||2.0 da/Nm|